[an error occurred while processing this directive]
化学工业与工程
 首页 |  在线投稿 |  期刊介绍 |  编 委 会 |  投稿指南 |  期刊订阅 |  下载中心 |  出版伦理 |  联系我们 |  English
化学工业与工程 2018, Vol. 35 Issue (2) :35-41,69    DOI: 10.13353/j.issn.1004.9533.20161124
化学反应与工艺 最新目录 | 下期目录 | 过刊浏览 | 高级检索 << | >>
PAC-PDMDAAC复合絮凝剂净化海水的絮凝特性及其絮凝条件优化
赵瑾, 王文华, 马宇辉, 姜天翔, 王静, 张雨山
国家海洋局天津海水淡化与综合利用研究所, 天津 300192
Flocculation of Composite Flocculant PAC-PDMDAAC for Seawater Purification and Its Optimum Coagulation Condition
Zhao Jin, Wang Wenhua, Ma Yuhui, Jiang Tianxiang, Wang Jing, Zhang Yushan
Institute of Seawater Desalination and Multipurpose Utilization, Tianjin 300192, China

摘要
参考文献
相关文章
Download: PDF (2077KB)   HTML ()   Export: BibTeX or EndNote (RIS)      Supporting Info
摘要 

以聚合氯化铝(PAC)和聚二甲基二烯丙基氯化铵(PDMDAAC)为原料制备了PAC-PDMDAAC复合絮凝剂,将其用于海水的净化处理。考察了PDMDAAC与Al的不同质量比对絮凝指数FI、形成絮体厚度及体系稳定动力学参数的影响,确定了PAC-PDMDAAC复合絮凝剂的PDMDAAC/Al最适宜配比。采用Box-Behnken响应面法分析了絮凝剂投加量、反应pH值之间的交互作用及其对浊度和CODMn去除效果的影响。实验结果表明:与聚合氯化铝(PAC)相比,PAC-PDMDAAC复合絮凝剂净化海水过程中形成絮体更大,沉降性能更好;随着PDMDAAC与Al质量比的增大,絮凝指数FI曲线上升越快速,絮体分层厚度越大,沉降速度越快,稳定动力学参数越大。PAC-PDMDAAC复合絮凝剂的最适宜混凝条件为:反应体系pH值为7.5,絮凝剂投加量为15.3 mg/L,在该条件下复合絮凝剂对海水CODMn和浊度的去除率均值分别为65.2%和87.4%,实验结果与响应曲面模型预测值基本相符。

Service
把本文推荐给朋友
加入我的书架
加入引用管理器
Email Alert
RSS
作者相关文章
赵瑾
王文华
马宇辉
姜天翔
王静
张雨山
关键词PAC-PDMDAAC复合絮凝剂   海水   絮凝   絮凝特性   响应面法     
Abstract

The composite flocculants were prepared using PAC (Polymeric aluminum chloride)and PDMDAAC (Poly dimethyl diallyl ammonium chloride) as raw materials, and was used in purification treatment of seawater. The coagulation process during the treatment of coastal seawater was evaluated by investigating flocculation index(FI), floc thickness and stability kinetics under different PDMDAAC/Al mass ratios. The Box-Behnken response surface methodology was used to study the combined effects of flocculant dosage and pH on turbidity and CODMn removal efficiency. The experimental results demonstrated that the composite flocculant had better flocculant efficiency than PAC. The increase in the PDMDAAC/Al mass ratio resulted in a larger flocculation index, flocs thickness and stability kinetics parameter, and the floc sedimentation rate was also increased. The optimal coagulation conditions for the treatment of seawater using PAC-PDMDAAC were as follows:pH 7.5, flocculant dosage 15.3 mg/L. Moreover, the maximum removal rate of CODMn and turbidity under optimal conditions reached up to 65.2% and 87.4% respectively, which were consistent with the predicted value by response surface methodology.

Keywordscomposite coagulation PAC-PDMDAAC;   seawater;   coagulation;   flocculation characteristics;   response surface methodology     
Received 2016-11-29;
Fund:

中央级公益性科研院所基本科研业务费专项资金项目(K-JBYWF-2016-T8)。

Corresponding Authors: 张雨山,E-mail:Yushanzhang@hotmail.com。     Email: Yushanzhang@hotmail.com
About author: 赵瑾(1982-),女,硕士,主要从事海水利用技术研究。
引用本文:   
赵瑾, 王文华, 马宇辉, 姜天翔, 王静, 张雨山.PAC-PDMDAAC复合絮凝剂净化海水的絮凝特性及其絮凝条件优化[J].  化学工业与工程, 2018,35(2): 35-41,69
Zhao Jin, Wang Wenhua, Ma Yuhui, Jiang Tianxiang, Wang Jing, Zhang Yushan.Flocculation of Composite Flocculant PAC-PDMDAAC for Seawater Purification and Its Optimum Coagulation Condition[J].  Chemcial Industry and Engineering, 2018,35(2): 35-41,69
Copyright 2010 by 化学工业与工程