胀接压力与初始间隙对换热器胀接质量的影响

摘要为研究换热管-管板胀接压力与初始间隙对换热器胀接质量的影响，采用胀接参数化模拟研究方法对液压胀接进行可靠性研究，建立换热管-管板胀接的弹塑性参数化几何模型，对不同的换热管-管板胀接压力和初始间隙进行研究，得到换热管残余等效应力、残余接触应力大小及分布规律。研究表明：胀接压力相同、间隙不同时，卸载后残余等效应力和残余接触应力值差别较小；初始间隙相同，胀接压力不同时，卸载后残余应力和残余接触应力值差别较大；换热管的残余等效应力和残余接触应力随着胀接压力的增大而增大，其变化趋势一致；当材料为Ti31钛合金、胀接压力为183 MPa时换热管与管板的初始间隙消除。研究结果为换热器最佳胀接性能优化及胀接质量的提高提供了依据。

	Service

	把本文推荐给朋友
	加入我的书架
	加入引用管理器
	Email Alert
	RSS
	作者相关文章
	段明德
	盛青志
	张壮雅
	杨保旭
	刘静波

关键词：换热器胀接压力初始间隙残余接触应力胀接质量

Abstract： In order to study the effects of heat transfer tube-tube plate expansion pressure and initial gap on heat exchanger expansion quality, the reliability of the hydraulic expansion joint was studied by the method of expansion parameterized simulation, and the elasto-plastic parameterized geometric model of heat exchange tube-tube plate expansion joint was established, and different expansion joint pressure and initial clearance of heat exchange tube-tube plate were performed. The residual equivalent stress, residual contact stress and distribution law of heat transfer tubes were obtained. The results show that when the expansion joint pressure is the same and the gap is different, the different of residual equivalent stress and residual contact stress value after unloading are smaller; When the initial gap is the same and the expansion pressure is different, residual stress and residual contact stress after unloading are quite different. The residual contact stress on the outer surface of the heat exchange tube increases with the increase of expansion joint pressure, and the residual equivalent stress also increases with the increase of the expansion joint force, and the change trend is consistent. When the material is Ti31 titanium alloy and the expansion pressure is 183 MPa, the initial clearance between heat exchanger tube and tube sheet is eliminated. The results provide the basis for optimizing the optimal expansion joint performance of heat exchangers and improving the quality of expansion joints.

Keywords： heat exchanger； expansion pressure； initial gap； residual contact stress； expansion quality

Received 2018-05-03;

Corresponding Authors: 盛青志,E-mail:shengqz0826@163.com。 Email: shengqz0826@163.com

About author: 段明德(1966-),男,博士,教授,现从事化工结构数值模拟的研究。

引用本文:

段明德, 盛青志, 张壮雅, 杨保旭, 刘静波.胀接压力与初始间隙对换热器胀接质量的影响[J]. 化学工业与工程, 2019,36(5): 70-79

Duan Mingde, Sheng Qingzhi, Zhang Zhuangya, Yang Baoxu, Liu Jingbo.Effect of Expansion Pressure and Initial Clearance on Expansion Joint Quality of Heat Exchanger[J]. Chemcial Industry and Engineering, 2019,36(5): 70-79

[1] 蒋祥荣, 李凯, 李大永, 等. 含支撑板结构的管-翅式换热器胀接工艺仿真[J]. 塑性工程学报, 2015, 22(4):93-98 Jiang Xiangrong, Li Kai, Li Dayong, et al. Finite element analysis of expand-joint forming of fin-tube heat exchanger with support planes[J]. Journal of Plasticity Engineering, 2015, 22(4):93-98(in Chinese)
[2] 宋京凯, 薛松龄, 姚祺峰, 等. 管板和传热管胀接应力应变的数值模拟及分析[J]. 哈尔滨工程大学学报, 2009, 30(6):639-643 Song Jingkai, Xue Songling, Yao Qifeng, et al. Numerical simulation of stress and strain of stube sheetand heat-transfer tubes[J]. Journal of Harbin Engineering University, 2009, 30(6):639-643(in Chinese)
[3] 刘宝亮, 闫秀娟, 刘军, 等. 聚丙烯中空纤维换热器的数值模拟[J]. 化学工业与工程, 2017, 34(1):90-95 Liu Baoliang, Yan Xiujuan, Liu Jun, et al. Numerical simulation for polypropylene hollow fiber heat exchanger[J]. Chemical Industry and Engineering, 2017, 34(1):90-95(in Chinese)
[4] 李伟, 王强, 杨笑瑾, 等. 镍基合金换热管与镍基合金管板液压胀接试验研究[J]. 化工机械, 2017, 44(4):386-389 Li Wei, Wang Qiang, Yang Xiaojin, et al. Experimental study on hydraulic expansion of nickel-base alloy tube to nickel-base alloy tubesheet[J]. Chemical Engineering & Machinery, 2017, 44(4):386-389(in Chinese)
[5] 王玉刚, 黄翔. 一种新型管式间接蒸发冷却器的性能[J]. 化工学报, 2012, 63(S2):49-52 Wang Yugang, Huang Xiang. Performance of a novel tubular indirect evaporative cooler[J]. CIESC Journal, 2012, 63(S2):49-52(in Chinese)
[6] 王晓静, 王磊, 郜维栋. 基于Ansys Workbench的换热管断裂行为模拟分析[J]. 化学工业与工程, 2016, 33(1):90-95 Wang Xiaojing, Wang Lei, Gao Weidong. Failure analysis of heat exchange tubes based on ansys workbench[J]. Chemical Industry and Engineering, 2016, 33(1):90-95(in Chinese)
[7] 杜婷婷, 杜文静, 程林. 新型椭圆管螺旋折流板换热器特性研究[J]. 工程热物理学报, 2018, 39(1):193-199 Du Tingting, Du Wenjing, Cheng Lin. Research on characteristics of a novel helical baffled heat exchanger with oval tubes[J]. Journal of Engineering Thermophysics, 2018, 39(1):193-199(in Chinese)
[8] 丁宇奇, 董日治, 刘巨保,等. 换热器管板与换热管胀接密封性能影响因素分析[J]. 化工机械, 2018,45(1):90-95 Ding Yuqi, Dong Rizhi, Liu Jubao, et al. Influencing factors of expansion and sealing performance of heat exchanger tube plate and heat exchanger[J]. Chemical Machinery, 2018, 45(1):90-95(in Chinese)
[9] Bouzid A H, Laghzale N E. Analytical modeling of tube-to-tubesheet joints subjected to plastic deformation and creep[J]. Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2016, 10(4):JAMDSM0055
[10] Merah N, Al-Aboodi A, Shuaib A N, et al. Combined effects of tube projection, initial tube-tubesheet clearance, and tube material strain hardening on rolled joint strength[J]. Journal of Pressure Vessel Technology, 2009, 131(5):051201
[11] Al-Aboodi A, Merah N, Shuaib A N, et al. Effects of friction on roller expanded tube-tubesheet joint strength[J]. International Journal of Material Forming, 2010, 3(4):253-257
[12] 倪鹏, 惠虎, 王晓东, 等. 蒸汽发生器管板液压胀管数值模拟研究[J]. 核动力工程, 2015, 36(5):204-207 Ni Peng, Hui Hu, Wang Xiaodong, et al. Numerical simulation of hydraulically expanded tube-to-tube sheet joints in steam generator[J]. Nuclear Power Engineering, 2015, 36(5):204-207(in Chinese)
[13] Akisanya A R, Khan F U, Deans W F, et al. Cold hydraulic expansion of oil well tubulars[J]. International Journal of Pressure Vessels and Piping, 2011, 88(11/12):465-472
[14] Merah N, Al-Aboodi A, Shuaib A N, et al. 3-D finite element analysis of roller-expanded heat exchanger tubes in over-enlarged tubesheet holes[J]. Applied Petrochemical Research, 2012, 1(1/2/3/4):45-52
[15] 闫宗宝, 王国珍, 轩福贞, 等. 核电蒸汽发生器管子与管板胀接力学行为与接头性能研究[J]. 核动力工程, 2011, 32(S1):173-178 Yan Zongbao, Wang Guozhen, Xuan Fuzhen, et al. Study on mechanical behavior of expanding tube-to-tubesheet and joint performance for steam generator of nuclear power[J]. Nuclear Power Engineering, 2011, 32(S1):173-178(in Chinese)
[16] 王相兵, 张响, 陈辉, 等. 胀接成形工艺对管翅式换热器结构性能的影响[J]. 塑性工程学报, 2016, 23(4):61-68 Wang Xiangbing, Zhang Xiang, Chen Hui, et al. Effects of expand-joint forming on structure performance of fin-tube heat exchanger[J]. Journal of Plasticity Engineering, 2016, 23(4):61-68(in Chinese)
[17] 倪鹏, 惠虎, 王晓东,等. 蒸汽发生器液压胀接保压时间及拉脱力的研究[J]. 原子能科学技术, 2015, 49(12):2234-2238 Ni Peng, Hui Hu, Wang Xiaodong, et al. Steam generator hydraulic expansion study on the time of holding pressure and pull-off force[J]. Atomic Energy Science and Technology, 2015, 49(12):2234-2238(in Chinese)
[18] 于洪杰, 钱才富. 液压胀接接头密封性能的力学表征[J]. 化工机械, 2010, 37(6):758-762 Yu Hongjie, Qian Caifu. Mechanical description of the tightness of hydraulic expanded tube joints[J]. Chemical Engineering & Machinery, 2010, 37(6):758-762(in Chinese)
[19] 李涛, 段成红. 换热管与管板连接接头的液压胀接压力分析[J]. 化工机械, 2016, 43(6):759-763 Li Tao, Duan Chenghong. Analysis of hydraulic expansion pressure for tube-to-sheet joints[J]. Chemical Engineering & Machinery, 2016, 43(6):759-763(in Chinese)