[an error occurred while processing this directive]
化学工业与工程
 首页 |  在线投稿 |  期刊介绍 |  编 委 会 |  投稿指南 |  期刊订阅 |  下载中心 |  出版伦理 |  联系我们 |  English
化学工业与工程 2023, Vol. 40 Issue (4) :37-49    DOI: 10.13353/j.issn.1004.9533.20210370
化工过程与设备 最新目录 | 下期目录 | 过刊浏览 | 高级检索 << | >>
Na2SO4循环流化床蒸发器中的颗粒碰撞行为和传热性能
姜峰1,3, 徐迪1, 齐国鹏2, 李修伦1
1. 天津大学化工学院, 天津 300072;
2. 天津职业大学生物与环境工程学院, 天津 300410;
3. 天津市化工安全与装备技术重点实验室, 天津 300350
Particle collision behavior and heat transfer performance in a Na2SO4 circulating fluidized bed evaporator
JIANG Feng1,3, XU Di1, QI Guopeng2, LI Xiulun1
1. School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072, China;
2. School of Biological and Environment Engineering, Tianjin Vocational Institute, Tianjin 300410, China;
3. Tianjin Key Laboratory of Chemical Process Safety and Equipment Technology, Tianjin 300350, China

摘要
参考文献
相关文章
Download: PDF (7536KB)   HTML ()   Export: BibTeX or EndNote (RIS)      Supporting Info
摘要 将流化床换热防垢节能技术和Na2SO4蒸发过程相结合,设计并构建了1套Na2SO4循环流化床蒸发装置。选用质量分数为20%的Na2SO4溶液作为液相工质,采用聚甲醛(POM)和碳化硅(SiC)颗粒作为惰性固体颗粒,考察了颗粒类型、颗粒加入量(1%~3%)、循环流速(0.37~1.78 m·s-1)和热通量(7.29~12.14 kW·m-2)等操作参数对于颗粒的碰撞行为和蒸发器传热性能的影响。研究结果表明,POM和SiC 颗粒的加入均可以强化传热。实验范围内,POM和SiC 颗粒的最大增强因子分别为9.5%和13.4%,所对应的操作参数分别为ε=1%,u=1.78 m·s-1,q=7.29 kW·m-2ε=3%,u=0.37 m·s-1,q=12.14 kW·m-2。液相和固相碰撞加速度信号的特征频率范围分别为0~1 000 Hz和6 000~17 000 Hz;汽相的产生可以显著增加其他相的碰撞强度。颗粒加入量增加,POM颗粒的标准偏差增大;SiC颗粒的标准偏差在循环流速较低时先减小、后增大,而在循环流速较高时增大。2种颗粒的流动沸腾传热系数受颗粒加入量的影响较小。循环流速增加,2种颗粒的标准偏差和传热系数均增大。热通量增加,2种颗粒的传热系数均明显减小。颗粒加入量较小时,2种颗粒的标准偏差随热通量的变化不明显。颗粒加入量较大时,POM颗粒的标准偏差随着热通量的增加而增大;SiC颗粒的标准偏差随热通量的变化受循环流速的影响。
Service
把本文推荐给朋友
加入我的书架
加入引用管理器
Email Alert
RSS
作者相关文章
姜峰
徐迪
齐国鹏
李修伦
关键词循环流化床蒸发器   颗粒碰撞行为   强化传热   硫酸钠   标准偏差     
Abstract: A Na2SO4 circulating fluidized bed evaporation apparatus is designed and built by combining the fluidized bed heat transfer and fouling prevention technology and the evaporation process of Na2SO4 solution. 20%(mass fraction) Na2SO4 solution is selected as the liquid working medium. Polyoxymethylene (POM) and silicon carbide (SiC) particles are selected as the inert solid particles. The effects of the operating parameters, such as particle type, the amount of added particles (1%~3%), circulation flow velocity (0.37~1.78 m·s-1) and heat flux (7.29~12.14 kW·m-2), on the particle collision behavior and heat transfer performance are investigated. The results show that the addition of the POM and SiC particles can enhance heat transfer. The maximum enhancement factors are 9.5% and 13.4% for the POM and SiC particles, respectively, and the corresponding operating parameters are ε =1%,u=1.78 m·s-1,q=7.29 kW·m-2ε =3%,u=0.37 m·s-1,q=12.14 kW·m-2. The characteristic frequency ranges of the collision acceleration signals are 0~1 000 Hz and 6 000~17 000 Hz for the liquid phase and solid phase, respectively. The generation of the vapor phase significantly strengthens the collision intensity of other phases. The standard deviation of the POM particles increases with the increase in the amount of added particles. The standard deviation of the SiC particles initially decreases and then increases at low circulation flow velocity but increases at high circulation flow velocity with the increase in the amount of added particles. The amount of added particles slightly influences the heat transfer coefficients of the two kinds of particles. The standard deviations and heat transfer coefficients of the two kinds of particles increase with the increase in circulation flow velocity. The heat transfer coefficients of the two kinds of particles obviously decrease with the increase in heat flux. The heat flux has no obvious effect on the standard deviation at low amount of added particles. At high amount of added particles, the standard deviation of POM particles increases with the increase in heat flux; however, the variation trend of the standard deviation of the SiC particles with heat flux is dependent on the circulation flow velocity.
Keywordscirculating fluidized bed evaporator   particle collision behavior   heat transfer enhancement   sodium sulfate   standard deviation     
Received 2021-05-09;
Fund:化学工程国家重点实验室开放项目(SKL-CHE-18B03);天津市科技支撑计划重点项目(2009ZCKFGX01900)。
Corresponding Authors: 姜峰,副教授,E-mail:jiangfeng@tju.edu.cn。     Email: jiangfeng@tju.edu.cn
About author: 姜峰(1975-),男,博士,副教授,现从事多相流强化传热与防、除垢方面的研究。
引用本文:   
姜峰, 徐迪, 齐国鹏, 李修伦.Na2SO4循环流化床蒸发器中的颗粒碰撞行为和传热性能[J].  化学工业与工程, 2023,40(4): 37-49
JIANG Feng, XU Di, QI Guopeng, LI Xiulun.Particle collision behavior and heat transfer performance in a Na2SO4 circulating fluidized bed evaporator[J].  Chemcial Industry and Engineering, 2023,40(4): 37-49
Copyright 2010 by 化学工业与工程